Industrial Storage //

32GB SSD IDE 44Pin 2.5" ATA 9000 (BGA) 90MB/s Wide Temp D2D9-32GJ20AWBES

IDE Solid State Flash Disk

Industrial Laptop Size 2.5 44pin IDE PATA Solid State disk. Extremly reliable based on Industrial Chips for Industrial / Embedded Applications
Wide Temp

The ATA9000 Solid State Disk is the next generation of storage device based on industrial flash memory technology, which emulates an ordinary magnetic hard disk.

Built for speed, these Solid State Storage Devices need no moving or spinning parts, and that makes no mechanical noise, suitable for used in portable or embedded system, which has only limited power consumption. The Flash Disk Drive products are also free from extra and special algorithm or some firmware driver. Just plug the unit into the IDE 44pin slots and operate it as same as a regular Hard Disk Drives.

These high-speed SSD units provide faster and higher performance storage solution for industrial application, embedded computing, high-speed networking, broadband communications, mobile computing, military, medical and aerospace

In Addition of high-performance, the devices are capable of withstanding a higher dree of enivornmental distress, delivering extreme endurance.

Flash in Disk (FiD) 2.5'' ATA6000 products provide high capacity 2.5-inch solid-state flash disk that electrically complies with ATA6 standard. InnoDisk FiD 2.5'' ATA6000 is 2.5-inch solid-state data storage systems under industrial environment. FiD 2.5'' ATA6000 supports PIO(0-4), Multiword DMA(0-2) and Ultra DMA(0-5) transfer modes. FiD 2.5" ATA6000 supports LBA addressing mode. 1.2 Pin

Specifications & Performance

  • FiD 2.5''ATA6000 is approved for CE requirements and FCC standards.
  • FiD 2.5''ATA6000 is fully compliant with RoHS directive, also known as Restriction of Hazardous Substances directive.

  • Burst Transfer Rate : 100MB/sec (UDMA5)
  • Sustained Read : 60MB/sec
  • Sustained Write : 40MB/sec
  • Average Latency : 0.4 ms
    Notes- InnoDisk FiD 2.5 SATA 6000 is not a magnetic rotating design. There is no seek or rotational latency required.

    Environmental Specification & Endurance

  • 3.4.1 Temperature Ranges
  • Operation Temperature Range: -14C to +85C
  • Storage Temperature : -45C to +95C
  • 3.4.2 Humidity
  • Relative Humidity: 10-95%, non-condensing
    Mean Time between Failures (MTBF): MTBF prediction results for various FiD 2.5" ATA6000 configurations. The analysis was performed using a RAM CommanderTM failure rate prediction.
    Failure Rate: The total number of failures within an item population, divided by the total number of life units expended by that population, during a particular measurement interval under stated condition.
    Mean Time between Failures (MTBF): A basic measure of reliability for repairable items: The mean number of life units during which all parts of the item perform within their specified limits, during a particular measurement interval under stated conditions.

    FiD 2.5'' ATA6000 Telcordia SR-332 GB, 25 C > 3,000,000
    PIO Data Transfer

    Peripherals reporting support for PIO mode 3 or 4 shall power-up in a PIO mode 0, 1 or 2. For PIO modes 3 and above, the minimum value of t0 is specified by word 68 in the IDENTIFY DEVICE parameter list. Table 6 defines the minimum value that shall be placed in word 68. IORDY shall be supported when PIO mode 3 or 4 are the current mode of operation.

    This drive is also available in 3.5 inch form factor with Expansion Kit

    Please contact us for more information