Industrial Storage // memorydepot.com

64GB 2.5" SATA 6000 Solid State Flash Disk Wide Temp D2S6-64GD11W2

64GB


Wide Temp

The SATA Solid State Disk Wide Temp is the next generation of storage device based on industrial flash memory technology, which emulates an ordinary magnetic hard disk.

Built for speed, these Solid State Storage Devices need no moving or spinning parts, and that makes no mechanical noise, suitable for used in portable or embedded system, which has only limited power consumption. The Flash Disk Drive products are also free from extra and special algorithm or some firmware driver. Just plug the unit into the SATA slots and operate it as same as a regular Hard Disk Drives.

These high-speed SSD units provide faster and higher performance storage solution for industrial application, embedded computing, high-speed networking, broadband communications, mobile computing, military, medical and aerospace

In Addition of high-performance, the devices are capable of withstanding a higher dree of enivornmental distress, delivering extreme endurance.


PRICING AND PRODUCT DETAILS
InnoDisk FiD 2.5 SATA 6000 products provide high capacity flash memory Solid State Drive (SSD) that electrically complies with Serial ATA (SATA) standard. InnoDisk FiD 2.5 SATA 6000 support SATA II standard (3.0GHz) with high performance. Sustain read is 60 MB per second, and sustain write is 40 MB per second. InnoDisk FiD 2.5 SATA 6000 uses standard 2.5-inch form factor, which can be used in laptop. InnoDisk FiD 2.5 SATA 6000 is also designed for industrial field.

The SSD have good performance, and have small latency time. It effectively reduces the booting time of operation system and the power consumption is less than hard disk drive (HDD). InnoDisk FiD 2.5 SATA 6000 can work in harsh environment. The SSD is vibration resistance, and can work in lower or higher temperature than HDD. InnoDisk FiD 2.5 SATA 6000 complies with ATA protocol, no additional drives are required, and the SSD can be configured as a boot device or data storage device.

General Specifications

  • interface Serial ATA II
  • SATA Transfer Mode PIO mode 0-4/ MwDMA mode 0-2/UDMA mode 0-6
  • Burst Speed Rate 300MB/sec.
  • Operation Temp -400C~+850C(Standard)
  • Storage Temp -550C~+950C
  • Vibration 5G(7~2000Hz)
  • Shock 1500G/0.5ms
  • ECC Technology High reliability base on the internal ECC function
  • MTBF >3,000,000 hours
  • R/W Endurance 2,000,000 times
  • DC Input Voltage +5V single power supply operation
  • Power Mode Auto stand-by mode

    Performance

  • Burst Transfer Rate : 3Gbps
  • Sustained Read : 60MB/sec
  • Sustained Write : 40MB/sec
  • Average Latency : 0.4 ms
  • InnoDisk FiD 2.5 SATA 6000 support following transfer mode:
  • PIO Mode: 0~4.
  • Multiword DMA: 0~2.
  • Ultra DMA: 0~5.
  • Serial ATA I: 1.5Gbps
  • Serial ATA II: 3.0Gbps

    Environmental Test

    Reliability Test conditions Reference Standards
    Vibration 7 Hz to 700 Hz, 2 g, 3 axes IEC 68-2-6
    Mechanical Shock Duration: 0.5ms, 1500 g, 3 axes IEC 68-2-27
    Unit Drop From a height of 1.5 m IEC 68-2-32


    Endurance

    Conditions: Telcordia SR-332 GB, 250C, > 3,000,000 Hours

  • Read Cycles: Unlimited Read Cycles.
  • Write /Erase Cycles: 2,000,000 Erase Cycles.
       >150 years - 50GB write-erase /day
  • Data Retention: 10 years.
  • Wear-Leveling Algorithm: support.
  • Bad Blocks Management: Support
  • Error Correct Code: Support

  • Operating Temperature Range:
    - Standard Grade: -100C to +700C
  • Storage Temperature Range:
    - Standard Grade: -450C to +950C

    Mechanical Specs.



    This drive is also available in 3.5 inch form factor with Expansion Kit

    Please contact us for more information