Industrial Storage //

32GB FiD 2.5" SATA 25000 (BGA)(iCell) D2SN-32GJ20ACAES

Industrial SATA Solid State Flash Disk

Industrial SLC SATA Solid State Flash Disk
Commercial Temp

The FiD SATA25000 provides High-Performance Storage for industrial application. It not only performs better in sequential data transfer, but also enhances random ata access for small files. FiD SATA25000 delivery a high level of performance and reliability to fulfill veries requirements.

InnoDisk FiD 2.5 SATA 25000 products provide high capacity flash memory Solid State Drive (SSD) that electrically complies with Serial ATA (SATA) standard. It supports SATA II standard (3.0GHz) with high performance. For SLC solution, sustain read is at 250 MB per second (max.), and sustain write is at 200 MB per second (max); Except sequential read/ write performance, InnoDisk FiD 2.5 SATA 25000 also enhances random data access for small files. Furthermore, InnoDisk FiD 2.5 SATA 25000 support TRIM for windows 7,

it can improves performance when deleting files. It designed with standard 2.5-inch form factor, which can beused in laptop.

InnoDisk FiD 2.5 SATA 25000 is designed for industrial field. The SSD have good performance, no latency time and small seek time. It effectively reduces the booting time of operation system and the power consumption is less than hard disk drive (HDD). InnoDisk FiD 2.5 SATA 25000 can work in harsh environment. The SSD is vibration resistance, and can work in lower or higher temperature than HDD.

InnoDisk FiD 2.5 SATA 25000 complies with ATA protocol, no additional drives are required, and the SSD can be configured as a boot device or data storage device.

What is the difference between "regular" version and [Version2]?
The [Version2] with part# ending with a "B" is simply a new revision of the model with an updated memory chip and firmware update, they have the exact same functionality and specifications. The [version 2] will be available in a longer time range and the "regular" version will phase out sooner. For a new project, we suggest to go with [Version2]

Mechanical Specification

Interface: Support SATA II Interface (3.0Gbps)
Capacity: Provide 2GB, 4GB,8GB, 16GB, 32GB

Wear Leveling
Flash memory can be erased a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit applies to each individual erase block in the flash device.InnoDisk FiD 2.5 SATA 25000 uses a wear-leveling algorithm to ensure that consecutive writes of a specific sector are not written physically to the same page in the flash. This spreads flash media usage evenly across all pages, thereby maximizing flash lifetime.

Environmental Specifications
Operating Temperature Range
  • Standard Grade: 00C to +700C
  • Industrial Grade: -400C to +850C
    Storage Temperature Range
  • Standard Grade: -550C to +950C
  • Industrial Grade: -550C to +950C
    Relative Humidity: 10-95% , Non-Condensing

  • Reliabily and Durability


     Test Conditions

    Reference Standards

    Vibration 7 Hz to 2KHz,3 axes, 20G IEC 68-2-6
    Mechanical Shock Duration: 105ms, 1500G, 3 Axes IEC 68-2-27
    Product Condition MTBF(Hours)
    InnoDisk FiD 2.5" SATA 25000 TELECORDIA SR-332 GB, 250C >4,000,000

    Transfer mode and Power consumption
    InnoDisk FiD 2.5" SATA 25000 uses a standard SATA pin-out.
  • PIO Mode: 0~4
  • Ultra DMA: 0~6
  • Serial ATA I 1.5Gbps
  • Serial ATA II 3.0Gbps

    Power Consumption Mode Power Consumption(mA)
    Read 450
    Write 560
    Idle 200

  • Electrical Specification
    Power Requirement Item Symbol Rating Unit
    Input voltage VIN +5DC +-5% 500mA(max.) V

    Mechanical Specification