Industrial Storage // memorydepot.com

16GB CFAST 100, industrial Storage Card SATA DCIT-16GT21C1D

EOL 16GB Commercial Temp The CFast 100 is a Storage Card with the same physical dimmension as a CompactFlash, but with a new SATA interface. CFast 1.0 Standard wich is designed with a 7+17 pin connector consisting of a SATA comptabile 7 pin signal connector and a 17pin power and control connector. Offering superior performance and data transfer up to 100 MB/s ( and sequential write up to 50MB/s ) PRICING AND PRODUCT DETAILS

InnoDisk CFast 100 series supports SATA III standard (3.0Gb/s) interface with good performance and thus performs faster data transfer rate. Sustain read can reach up to 100MB per second (max), and sustain write reach up to 50MB per second (max). InnoDisk CFast 100 is suitable in industrial field. It effectively reduces the booting time of operation system and the power consumption is less than hard disk drive (HDD). InnoDisk CFast 100 can work under harsh environment. InnoDisk CFast 100 complies with ATA protocol, no additional drives are required, and the SSD can be configured as a boot device or data storage device General Specifications Interface: Serial ATA II (3.0Gbps) NAND Flash Memory: SLC (Single Level Cell ) Capacity: 2GB~16GB  Data transfer rate: Read- 100MB/sec., Write- 50MB/sec. Burst Transfer Rate: 150MB/sec. Compact Design: Buil-in Power pin (pin 7) Access time: 0.3ms Error Correction Function: Built-in ECC corrects up to 8-bit per 512-Byte Dimension: 42.8x36.4x3.6mm Weight: 10g±2g Boot No additional device drivers are required. The SATADOM can be configured as a boot device. Any Operating system can be installed. Electrical connection A Serial ATA device may be either directly connected to a host or connected to a host through a cable. For connection via cable, the cable should be no longer than 1meter. The SATA II Interface has a separate connector for the power supply. Please contact us if you need a model with a Built-in Power from the Sata connection. Wear Leveling Flash memory can be erased within a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit appliesto each individual erase block in the flash device. InnoDisk CFast 100 uses a static wear-leveling algorithm to ensure that consecutive writes of a specific sector are not written physically to the same page and block in the flash. This spreads flash media usage evenly across all pages, thereby extending flash lifetime. Environmental Specifications Operating Temperature Range Standard Grade: 0°C to +70°C Industrial Grade: -40°C to +85°C Storage Temperature Range Standard Grade: -55°C to +95°C Reliabily and Durability Reliability    Test Conditions Vibration     7 Hz to 2000 Hz, 20G, 3 axes  Mechanical Shock: 50G/10ms, 3 axes Product Condition MTBF (Hours): InnoDisk CFast 100 Telcordia SR-332 GB, 25°C > 3,000,000 Write /Erase Cycles: 2,000,000 Erase Cycles. Data Retention: 10 years. Support Wear-Leveling Algorithm Support Bad Blocks Management Transfer mode and power consumption InnoDisk CFast 100 supports the following transfer mode: PIO Mode: 0~4 Multiword DMA: 0~2 Ultra DMA: 0~6 InnoDisk CFast 100 power consumption Parameter           mA Sustained Read   155 Sustained Write   170 IDLE                  105 Note: Measured with device 8GB (SLC) Manual CHS Value Capacity LBA Cylinders Heads Sectors 512MB 983,040 975 16 63 1GB 1,966,080 1950 16 63 2GB 3,932,160 3900 16 63 4GB 7,864,320 7801 16 63 8GB 15,728,640 15,603 16 63 16GB 31,457,280 16,383 16 63