Industrial Storage // memorydepot.com

4GB EDC4000 40Pin Horizontal Type A Dual Channel DE0PA-04GD31CXD

IDE Disk on Module 40 Pin Horizontal
4GB

Very light weight, reliable & performant. Boot like regular Hard Disk. Comes with a power cable. Based on Industrial SLC chips
Commercial Temp

Extremely light weight, reliable & performant, This new generation IDE Flash Module made of SLC Industrial Nand Flash Memory, is the most flexible solution to provide reliable storage on space limited and hostile environnment. Decreasing data access time and replacing any moving part from a traditional hard drive, the Flash Disk on Module fit the needs of a wide range of application.

100% Compatible with the Standard IDE ATA interface, this unit works exaclty like a standard hard drive but without any moving part, strongly increasing reliability and improving data access speed performance, without any noise.

Model variation
Also available in Vertical Format


PRICING AND PRODUCT DETAILS
Note: The difference between Single Channel and Dual Channel impact on the speed only, where the Dual Channel offer twice the read/write transfer speed performance compared to the single channel, since they are made of 2 chips that can be accessed simultaneously. This does not affect the compatibility and both models will be similarly recognised by the motherboard..

Embedded Disk Card 4000 (EDC4000) products provide high capacity solid-state flash memory that electrically complies with the Personal Computer Memory Card International Association ATA standard.
InnoDisk Embedded Disk Card 4000 (EDC4000) is embedded solid-state data storage systems for industrial work place. Embedded Disk Card 4000 (EDC4000) features an extremely light weight, reliable, low-profile form factor.
Embedded Disk Card 4000 (EDC4000) supports advanced PIO (0-4), Multi Word DMA (0-2), Ultra DMA (0-4) transfer modes, multi-sector transfers, and LBA addressing.

General Specifications

Burst Transfer Rate : 66.6Mbps
Sustained Read :
  • Dual Channel: 40Mbps
  • Single Channel: 20Mbps
    Sustained Write :
  • Duel channel: 20Mbps
  • Single Channel: 10Mbps
    Average Latency : 0.4 ms
    DC Input Voltage: +3.3V/+5V Single power supply
    Dimension: 48.20/32.60/7.3 mm (W/T/H)
    Compatibility: CE  and FCC standards


  • Wear Leveling

    Flash memory can be erased within a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit applies to each individual erase block in the flash device. EDC 4000 uses a wear-leveling algorithm to ensure that consecutive writes of a specific sector are not written physically to the same page/block in the flash. This spreads flash media usage evenly across all pages, thereby extending flash lifetime.


    Environmental Specifications

    Operating Temperature Range
    Standard Grade: -100C - +700C
    Storage Temperature Range
    Standard Grade: -450C to +950C
    Reliabily and Durability
    Reliability Test Conditions
    Vibration: 7 Hz to 700Hz, 2 g, 3 axes
    Mechanical Shock Duration: 0.5ms, 1500 g, 3 axes
    Drop Unit: From a height of 1.5 m
    Product Condition MTBF (Hours):  Telcordia SR-332 GB, 25 0CC > 3,000,000



    Manual CHS Value
    Capacity Cylinders Heads Sectors LBA
    32MB 500 8 16 64000
    64MB 500 8 32 128000
    128MB 500 16 32 256000
    256MB 1000 16 32 512000
    512MB 1015 16 63 1023120
    1GB 2031 16 63 2047248
    2GB 4063 16 63 4095504
    4GB 8146 16 63 8211168
    8GB 16000 16 63 16128000



    Mechanical Specs