Industrial Storage // memorydepot.com

W/T8G Mini PCIe 8 channels DMPE-08GJ13W1

PCIE Disk on Module
8GB


Commercial Temp

The Mini PCIe Disk on Module (mini DOM) series supports SATA II standard (3.0Gb/s) and USB 2.0 interface with good performance and thus performs faster data transfer rate. Sustain read can reach up to 100MB per second (max), and sustain write reach up to 60MB per second (max). Moreover, InnoDisk mini DOM is designed as the standard Mini PCIe form factor, and compatible with Mini PCIe slot


PRICING AND PRODUCT DETAILS

InnoDisk Mini PCIe Disk on Module (mini DOM) series supports SATA II standard (3.0Gb/s) and USB 2.0 interface with good performance and thus performs faster data transfer rate. Sustain read can reach up to 100MB per second (max), and sustain write reach up to 60MB per second (max). Moreover, InnoDisk mini DOM is designed as the standard Mini PCIe form factor, and compatible with Mini PCIe slot.
InnoDisk mini DOM is suitable in industrial field, it effectively reduces the booting time of operation system and the power consumption is less than hard disk drive (HDD). It can work under harsh environment, complies with ATA protocol, no additional drives are required, and can be configured as a boot device or data storage device.

General Specifications

Interface: Serial ATA II 3.0Gbps, USB 2.0
Capacity: 2GB~16GB
Form factor: Standard Mini PCIe
Data transfer rate: Read- 100MB/sec., Write- 60MB/sec.
Burst Transfer Rate: 300MB/sec.
Power Requirement: 3.3V DC single power supply
Access time: 0.3ms
Error Correction Function: Built-in ECC corrects up to 8-bit per 512-Byte
Dimension: 30x50.95x3.4mm
 


Boot

No additional device drivers are required. The InnoDisk mini DOM can be configured as a boot device.


Electrical connection

A Serial ATA device may be either directly connected to a host or connected to a host through a cable. For connection via cable, the cable should be no longer than 1meter. The SATA interface has a separate connector for the power supply. Please contact us if you need a model with a Built-in Power from the Sata connection.

Wear Leveling

Flash memory can be erased within a limited number of times. This number is called the erase cycle limit or write endurance limit and is defined by the flash array vendor. The erase cycle limit applies to each individual erase block in the flash device. InnoDisk mini DOM uses a static wear-leveling algorithm to ensure that consecutive writes of a specific sector are not written physically to the same page and block in the flash. This spreads flash media usage evenly across all pages, thereby extending flash lifetime.


Environmental Specifications

Operating Temperature Range
Standard Grade: 00C to +700C
Industrial Grade: -400C to +850C
Storage Temperature Range
Standard Grade: --550C to +950C

Reliabily and Durability
Reliability Test Conditions
Vibration: 7 to 2000 Hz, 20G, 3 axes
Mechanical Shock Duration: Duration: 10ms, 50G, 3 axes


Product Condition MTBF (Hours): InnoDisk mini DOM Telcordia SR-332 GB, 250C > 3,000,000

Transfer mode and power consumption

InnoDisk mini DOM supports the following transfer mode:
PIO Mode: 0~4
Multiword DMA: 0~2
Ultra DMA: 0~6

InnoDisk mini DOM power consumption
 
Parameter mA
Sustained Read 206
Sustained Write 186
IDLE 112

Note: Measured with 8GB device



Manual CHS Value
Capacity Cylinders Heads Sectors LBA
2GB TBD TBD TBD TBD
4GB 7801 16 63 7,863,408
8GB 15,603 16 63 15,728,824
16GB 16,383 16 63 31,457,280

Mechanical Specs