Industrial Storage //

32GB 2.5" ATA 6000 Flash in Disk Wide Temp D2D6-32GD11W1

IDE Solid State Flash Disk

Industrial Laptop Size 2.5 44pin IDE PATA Solid State disk. Extremly reliable based on Industrial Chips for Industrial / Embedded Applications
Wide Temp

The ATA6000 Solid State Disk is the next generation of storage device based on industrial flash memory technology, which emulates an ordinary magnetic hard disk.

Built for speed, these Solid State Storage Devices need no moving or spinning parts, and that makes no mechanical noise, suitable for used in portable or embedded system, which has only limited power consumption. The Flash Disk Drive products are also free from extra and special algorithm or some firmware driver. Just plug the unit into the IDE 44pin slots and operate it as same as a regular Hard Disk Drives.

These high-speed SSD units provide faster and higher performance storage solution for industrial application, embedded computing, high-speed networking, broadband communications, mobile computing, military, medical and aerospace

In Addition of high-performance, the devices are capable of withstanding a higher dree of enivornmental distress, delivering extreme endurance.

Model variation
ATA 6000 - Commercial Temp -10 +70
ATA 6000 - Wide Temp -40 +80

InnoDisk FiD 2.5 SATA 6000 products provide high capacity flash memory Solid State Drive (SSD) that electrically complies with Serial ATA (SATA) standard. InnoDisk FiD 2.5 SATA 6000 support SATA II standard (3.0GHz) with high performance. Sustain read is 60 MB per second, and sustain write is 40 MB per second. InnoDisk FiD 2.5 SATA 6000 uses standard 2.5-inch form factor, which can be used in laptop. InnoDisk FiD 2.5 SATA 6000 is also designed for industrial field.

The SSD have good performance, and have small latency time. It effectively reduces the booting time of operation system and the power consumption is less than hard disk drive (HDD). InnoDisk FiD 2.5 SATA 6000 can work in harsh environment. The SSD is vibration resistance, and can work in lower or higher temperature than HDD. InnoDisk FiD 2.5 SATA 6000 complies with ATA protocol, no additional drives are required, and the SSD can be configured as a boot device or data storage device.

Product Informations

  • Burst Speed Rate 300MB/sec.
  • Operation Temp -400C~+850C(Standard)
  • Storage Temp -550C~+950C
  • Vibration 5G(7~2000Hz)
  • Power Mode Auto stand-by mode
  • Shock 1500G/0.5ms
  • ECC Technology High reliability base on the internal ECC function
  • MTBF >3,000,000 hours
  • R/W Endurance 2,000,000 times
  • DC Input Voltage +5V single power supply operation
  • Performance

  • Burst Transfer Rate : 3Gbps
  • Sustained Read : 60MB/sec
  • Sustained Write : 40MB/sec
  • Average Latency : 0.4 ms
  • InnoDisk FiD 2.5 SATA 6000 support following transfer mode:
  • PIO Mode: 0~4.
  • Multiword DMA: 0~2.
  • Ultra DMA: 0~5.
  • Environmental Test
    Vibration 7 Hz to 700 Hz, 2 g, 3 axes IEC 68-2-6
    Mechanical Shock Duration: 0.5ms, 1500 g, 3 axes IEC 68-2-27
    Unit Drop From a height of 1.5 m IEC 68-2-32


  • Read Cycles: Unlimited Read Cycles.
  • Write /Erase Cycles: 2,000,000 Erase Cycles.

  • >150 years @ 50GB write-erase /day
  • Data Retention: 10 years.
  • Wear-Leveling Algorithm: support.
  • Bad Blocks Management: Support
  • Error Correct Code: Support
  • Operating Temperature Range:

  • >Standard Grade: -100C to +700C
  • Storage Temperature Range:

  • >Standard Grade: -450C to +950C