Industrial SATA Storage Card CFAST 100 (end of life)
The CFast 100 is a Storage Card with the same physical dimmension as a CompactFlash, but with a new SATA interface. CFast 1.0 Standard wich is designed with a 7+17 pin connector consisting of a SATA comptabile 7 pin signal connector and a 17pin power and control connector. Offering superior performance and data transfer up to 100 MB/s ( and sequential write up to 50MB/s )
Commercial Temperature Operating Range: 0c to +70c
|
|
Product listing
Specifications
InnoDisk CFast 100 series supports SATA III standard (3.0Gb/s) interface with
good
performance and thus
performs faster data transfer rate. Sustain read can reach
up to
100MB per second (max), and sustain write reach
up to 50MB per second (max).
InnoDisk CFast 100 is suitable in industrial field. It effectively reduces the
booting
time
of operation system and the power consumption is less than hard disk drive (HDD).
InnoDisk CFast 100 can
work under harsh environment. InnoDisk CFast 100 complies
with ATA protocol, no additional drives are required,
and the SSD can be
configured
as a boot device or data storage device
 |
Interface: Serial ATA II (3.0Gbps)
NAND Flash Memory:
SLC (Single Level Cell )
Capacity: 2GB~16GB
Data transfer rate: Read- 100MB/sec., Write- 50MB/sec.
Burst Transfer Rate: 150MB/sec.
Compact Design: Buil-in Power pin (pin 7)
Access time: 0.3ms
Error Correction Function: Built-in ECC corrects up to 8-bit per 512-Byte
Dimension: 42.8x36.4x3.6mm
Weight: 10g±2g
|
 |
No additional device drivers are required. The SATADOM can be configured as a boot device.
Any Operating system can be installed.
|
 |
A Serial ATA device may be either directly connected to a host or connected to a
host
through a cable. For connection via cable, the cable should be no longer
than 1meter.
The SATA II Interface has a separate connector for the power supply. Please contact us
if you need a model with a Built-in Power from the Sata connection.
|
 |
Flash memory can be erased within a limited number of times. This number is
called the erase
cycle limit or write endurance limit and is defined by the
flash array vendor. The erase cycle
limit appliesto each individual erase block
in the flash device. InnoDisk CFast 100 uses a
static wear-leveling algorithm to
ensure that consecutive writes of a specific sector are not
written physically
to the same page and block in the flash. This spreads flash media usage
evenly
across all pages, thereby extending flash lifetime. |
 |
Operating Temperature Range
Standard Grade: 0°C to +70°C
Industrial Grade: -40°C to +85°C
Storage Temperature Range
Standard Grade: -55°C to +95°C
|
 |
Reliability Test Conditions
Vibration 7 Hz to 2000 Hz, 20G, 3 axes
Mechanical Shock: 50G/10ms, 3 axes
Product Condition MTBF (Hours):
InnoDisk CFast 100 Telcordia SR-332 GB, 25°C > 3,000,000
Write /Erase Cycles: 2,000,000 Erase Cycles.
Data Retention: 10 years.
Support Wear-Leveling Algorithm
Support Bad Blocks Management
|
 |
InnoDisk CFast 100 supports the following transfer mode:
PIO Mode: 0~4
Multiword DMA: 0~2
Ultra DMA: 0~6
InnoDisk CFast 100 power consumption
Parameter mA
Sustained Read 155
Sustained Write 170
IDLE
105
Note: Measured with device 8GB (SLC) |
| Capacity |
LBA |
Cylinders |
Heads |
Sectors |
| 512MB |
983,040 |
975 |
16 |
63 |
| 1GB |
1,966,080 |
1950 |
16 |
63 |
| 2GB |
3,932,160 |
3900 |
16 |
63 |
| 4GB |
7,864,320 |
7801 |
16 |
63 |
| 8GB |
15,728,640 |
15,603 |
16 |
63 |
| 16GB |
31,457,280 |
16,383 |
16 |
63 |
Other models available ( Variation)
 |
Looking for pricing?
You can get sample price by clicking on the "details" button on each capacity.
If you need to get a budgetary price for your project, please contact us
|
|
|
Need technical info or advices?
Our mission is to help you finalizing your project successfully. By giving you some advices, we can help you reducing cost and time to market
Here is where you can reach us
|
|
|
FULL PRODUCT LISTING
REQUEST A QUOTE
TECHNICAL SUPPORT
DCIT-02GT21C1D
